1.25Gbps SFP EZR Transceiver,1550nm,200km

This is a high-performance solution designed to overcome the challenges of ultra-long-distance transmission. By integrating optical amplification technology, it achieves an impressive 200 km of unrepeatered transmission within a standard SFP form factor. It is primarily used in telecommunications backbone networks and dedicated network interconnections where extreme distance requirements exist.

contact us:lina@glhcoptical.com

 

Product Features

Ø Single +3.3V power supply

Ø Up to 1.25Gb/s Data Links

Ø Hot-Pluggable

Ø Duplex LC connector

Ø Up to 200km on 9/125μm SMF

Ø 1550nm COOLED DFB laser transmitter

Ø APD Receiver

Ø Single +3.3V Power Supply

Ø Monitoring Interface Compliant with SFF-8472

Ø Maximum Power<1.5W

Ø Operating temperature range:Commercial: 0°C to 70°C,Industrial: -40°C to +85°C

Ø RoHS compliant and Lead Free

 

 

Applications

Ø 1000BASE Ethernet

Ø Switch/Router

Ø 1×Fibre Channel

Ø Other Optical Links

 

 

Description

This Transceiver is a high performance, cost effective module which have a duplex LC optics interface. Standard AC coupled CML for high speed signal and LVTTL control and monitor signals. The receiver section uses an APD receiver and the transmitter uses a 1550 nm DFB laser, up to 42dB link budge ensure this module 1000Base Ethernet 200km application.

 

 

 

Absolute Maximum Ratings

Table 1-Absolute Maximum Ratings

 

Parameter

Symbol

Min

Max

Unit

Note

Storage Temperature

TS

-40

85

°C

 

Operating Case Temperature

TOP

0

70

°C

 

Power Supply Voltage

VCC

-0.5

3.6

V

 

Relative Humidity (non-condensation)

RH

0

85

%

 

 

 Note:

It has to be noted that the operation in excess of any individual absolute maximum ratings might cause permanent damage to this module.

 

  

 

Recommended Operating Conditions

Table 2 -Recommended Operating Conditions

 

Parameter

Symbol

Min

Typical

Max

Unit

Note

Operating Case Temperature

TOP

0

 

70

°C

 

Power Supply Voltage

VCC

3.135

3.3

3.465

V

 

Power Consumption

P

 

 

1

W

 

Supply Current

Icc

 

 

300

mA

 

Aggregate Bit Rate

BRAVE

-

1.25

-

Gb/s

 

Bit Error Rate

BER

 

 

10-12

 

 

Transmission Distance

TD

 

-

200

KM

Over SMF

 

 

Optical Characteristics

Table 3-Optical Characteristics

 

Transmitter Optical Specification

Parameter

Symbol

Min

Typ

Max

Units

Notes

Center Wavelength

λc

1530

1550

1570

nm

 

Spectral Width

σ

 

 

1

nm

 

Side Mode Suppression Ratio

SMSR

30

 

 

dB

 

Optical Output Power

Pout

+3

 

+7

dBm

1

Extinction Ratio

ER

9

 

 

dB

 

Optical Rise/Fall Time

tr / tf

 

 

260

ps

2

Relative Intensity Noise

RIN

 

 

-120

dB/Hz

 

Output Eye Mask

 

Compliant with IEEE802.3 z (class 1 laser safety)

 

 

 Note:

1、The optical power is launched into SMF.

2、220-80%.

3Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.

4Measured with PRBS 27-1 at 10-12 BER

 

 

Receiver Optical Specification

Parameter

Symbol

Min

Typ

Max

Units

Note

Optical Input Wavelength

λc

1270

 

1610

nm

 

Receiver Overload

Pol

-7

 

 

dBm

1

RX Sensitivity

Sen

 

 

-37

dBm

2

RX_LOS Assert

LOS A

-46

 

 

dBm

 

RX_LOS De-assert

LOS D

 

 

-39

dBm

 

RX_LOS Hysteresis

LOS H

0.5

 

 

dB

 

Note:

1、Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.

2Measured with PRBS 27-1 at 10-12 BER

 

 

Electrical Characteristics

The following electrical characteristics are defined over the recommended operating environment

 

Table 4-Electrical Characteristics

 

Parameter

Symbol

Mi

Typ

Max

Units

Notes

Transmitter (Module Input)

Input differential impedance

Rin

90

100

110

 

 

Single ended data input swing

Vin PP

250

 

1200

mVp-p

 

Transmit Disable Voltage

VD

Vcc  1.3

 

Vcc

V

1

Transmit Enable Voltage

VEN

Vee

 

Vee+ 0.8

V

 

Transmit Disable Assert Time

Tdessert

 

 

10

us

 

Receiver (Module Output)

Single ended data output swing

Vout,pp

250

 

800

mv

2

LOS Fault

Vlosfault

Vcc  0.5

 

VCC_host

V

3

LOS Normal

Vlos norm

Vee

 

Vee+0.5

V

3

Power Supply Rejection

PSR

100

 

 

mVpp

4

 

 Note:

1Or open circuit. 220 – 80 %

3LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.

4All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to

1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.

 

 

 

 

If you need more support , Please contact us .